How to Get Free MB Tokens for Xhorse?

 How to Get Free MB Tokens for VVDI MB or Key Tool Plus?

Combining the key cutting machine serial number and the device serial number allows you to earn up to 2 free MB tokens per day!

NOTE:
*The tokens are not cumulative and are refreshed daily.
*Both types of devices (key cutting machine + VVDI KEY TOOL PLUS/VVDI MB TOOL) must be combined.
*The serial number of the device needs to be sent to your local dealer for uploading to the system for combining.
*Combining Panda Series Key Cutting Machines cannot get tokens.

Xhorse MVCI Pro V2.1.9 Adds Nissan Volvo Benz Drivers

 Great News! The Xhorse MVCI PRO J2534 now supports more diagnostic software brands like Benz, Maybach, Volvo, Renault and more, all tested on real vehicles for top reliability. Start solving diagnostic challenges for more vehicle brands today!

Software version V2.1.9
Firmware version: V1.3.4

Newly Supported Diagnostic Sofware Brands

Benz
Volvo
Nissan
Peugeot
Chevrolet Cadillac

Compatible brands and software (keep updating)

Mercedes Benz, Maybach, Smart Xentry
Volvo VIDA
Nissan Consult III Plus
Peugeot Diagbox
Renault CLIP
GM Tech2win/GDS2/RDS
Toyota Lexus Techstrea,
Honda Acura HDS
Subaru SSM-IV
Ford IDS FDRS
Mazda IDS

Xhorse Multi Prog 9S12XDT256 Chip Verification Failed?

 Problem:

Xhorse Multi prog At first it worked well with Flash and EEPROM of 9s12XDT256 SsangYong Tivoli, but now the following chip data verification failed error occurs.

Solution:

There are unsecured and secured options.

Choose 9s12XDT256 secured option and read again.

www.vvdishop.com

Xhorse Multi Prog Fails to Unlock VW D70F3426 Solution

 Problem:

I read JC dash from VW golf 7 cluster mcu D70F3426 with Xhorse multi prog, not possible unlock 70f3426, detection is ok but not unlock.

Solution:

Power on the Multi standard adapter to start up the programmer.

You might have this problem:
And also 12V power directly on the adapter, via connector.

Been there, found out the hard way.

 

 

Feedback:

Unlock mcu in second as said above.

Xhorse VVDI2 or AVDI to Program Audi A3 Micronas Key?

 Question:

Having a few too many issues reading this Audi A3 P8 Micronas cluster on bench with Abrites + ZN060 Micronas cluster adapter. Maybe VVDI2 would be better? is it possible to wake up this cluster on bench with VVDI2?

 

Here is the clue.

A3 Micronas with blue connector is not possible with pogo pin to service mode and read immo data, you will need to service mode by eeprom.

A3 micronas cluster with blue connector has no support for reading immo data by ANY tool.

You will have to read EEPROM(24c64 from memory),write modified eeprom on bench, replace cluster in car, write back original by obd and then read immo data by OBD with a supporting tool. Xhorse VVDI2/VVDI Key Tool Plus can do this from start to finish.

There’s plenty of guides on how to do TP2 service mode by EEPROM online, but the xhorse tools mostly automate it, just feed the file in and write back the result file then continue to write back by obd/read immo data.

 

 

24c32 in this one.  People have done a few this way with Key tool plus and VVDI Prog. Better have the cluster on the bench and try to avoid connecting the cluster in the car and lose the ABS coding.

 

Feedback:

Well, did the needed… and now it works.

Pin 1 +12V (30)
Pin 4 GND (31)
Pin 5 +12V (15)

Pin 29 CAN H
Pin 30 CAN L

Connected in bench and VVDI 2 did it’s magic.

 

Abrites software is busted for OBD reading on 8P platform A3. It was reported to them several times and that was quite some time ago but they obviously don’t have any interest in fixing it. VVDI does the job for me.

 

www.vvdishop.com

Xhorse VVDI2 Small Screen “Updating” Solution

 Problem:

Pulled Xhorse VVDI2 out of box this morning plugged it in and the small screen shows updating icon in Chinese. Any idea?

Possible reason:

You unplugged the USB cable before the upgrade was fully completed last time. So it shows in upgrade status.

 

Solution:

1.Update VVDI2 firmware via Xhorse Upgrade kit on laptop.

2. Change USB port or another laptop, try again. If all fails, the device may need a factory repair.

 

www.vvdishop.com

How to Add Audi A8 BCM2 Smart Key with Xhorse VVDI2?

 It is an Audi A8 2018, and it’s a keyless one with a push-to-start key. We will walk you through the entire process using the Xhorse VVDI2 key programmer. From setup to completion, you’ll see all the steps needed to successfully create a copy of an advanced keyless system.

Tool used:

Xhorse VVDI2

Xhorse vvdi key tool max

Xhorse XM38 754J remote

Original Audi key

 

Step:

Generate remote

Read Immo data

Make dealer key

Learn key

 

Procedure:

1. Generate remote

Generate remote under 754D Prox 868 option using XM38 754J remote

Step 2: Read Immo data

Run VVDI2 software.

Select Key Learning-> 5th Immobilizer system
Then hit Read BCM2 Data (OBDII)

Save immo data

Step 3: Make dealer key

Press Make dealer key

Prepare normal dealer key

Select A6L, A7, A8, Touareg add key

Put original key into vvdi2 programmer.

Load BCM2 data read in step 2.

Make dealer key successfully.

Step 4: Learn key

Select Key Learning.

Follow VVDI2 prompts to learn both keys.

All keys have been learned.

www.vvdishop.com

Xhorse Multi Prog Pinout to PSA Valeo V56.12

 Question:

I have to read a Citroen C3 1.2 Petrol ECU V56.12 but the wiring connection in Xhorse Multi Prog Boot Mode is missing.

Solution:

Multi Prog does PSA Valeo V56.x in boot mode only.

Here is the boot mode pinout.

Xhorse Key Tool Max Pro Add Peugeot ID48 key Marelli IMMO

 Question:

Will Xhorse VVDI Key Tool Max Pro Add a Key to my Peugeot Boxer 2.2 2009 with magneti marelli immo?

 

Yes, key tool max pro will add a spare key to Peugeot Citroen ID48 with Marelli IMMO system.

Go to IMMO system (Marelli 70F3238 + 95320 ID48) function.

Supports read eeprom, write eeprom, make dealer key, key programming, adapt remote key and renew remote.

If need to add a new key, follow steps below to finish key programming.

FYI:

If your car has id46 transponder then no problem for you, can use precoded transponder and program in car via diagnostic device but if is immo3 with id48 than you need special precoded id48 chip from vin from dealer or need make transponder with key maker from dump and need rewrite new dump which will be produce during transponder programing. in this mean the transponder is ready to start car.

www.vvdishop.com

Xhorse FT OBD Tool Add Toyota Camry 2013-2017 Smart Key

 How to erase and add a smart key for your Toyota vehicle using the VVDI Key Tools Max and Xhorse FT-OBD tool. This is a step-by-step guide on how to program a Toyota Camry smart key using the Mini FT tool. You can also run App on a mobile phone instead of key tool max. The Xhorse FT-Mini OBD tool is a Toyota specific tool that can be used to program smart keys for a variety of Toyota models, including the Toyota Camry, Sequoia, RAV4, and 4Runner up to 2023. We will demonstrate how to use the Xhorse FT-OBD tool to complete the programming process. With these tools, you’ll be able to delete and add smart keys with ease. 

Take an example of Camry 2015 smart key.

Select IMMO Programming- Select from model- Camry- KeylessGo- 2013-2017 Type 1(8A-Page P4 88)

If all keys lost, you need to perform all these steps.

Step 1: Read EEPROM data
Step 2: Generate emergency key
Step 3: Add keys

Here just add a spare key, so choose Adding Keys.

Select Clear smart keys.
Turn the ignition to ON position.

Xhorse FT OBD Tool detects that 1 key was registered.

Touch the ignition with a registered key within 30s.

Erase key successfully.

Select Add smart keys
Turn the ignition to ON position.
Keep the ignition switch with a registered key with the marked surface within 30s.

Key detected. prgramming…
Keep the key touching the igntion switch.

Register a new key successfully.

Test the new key and remote control.

Check:

https://www.vvdishop.com/service/how-to-bine-xhorse-ft-mini-obd-tool.html