Xhorse VVDI Tools, VVDI2, VVDI MB, VVDI Prog, VVDI key tool, VVDI BMW etc software & firmware download, update and technical support from vvdishop.com.
Problem:
I cannot program the generated file in the new (KYDZ MLB) key. The Xhorse VVDI MLB Tool adapter recognizes the key, but at the time of programming it shows that it is not found or blocked. When I simply check the key, that see it.
Solution:
You can’t generate dealer key on kydz key with vvdi tool. If you want to use vvdi MLB tool only OEM virgin key or vvdi special key. Kydz works only with kydz MLB tool.
Xhorse MLB specialized key is not yet released. So use original key.
Question: Is it possible to generate MQB48 transponder from xt27A or xt27B vvdi super chip to be used in VW cars post-2018 to star the car? Pic is from Xhorse VVDI Key Tool Max Pro.
Solution:
Xt27b is on available in the b5 remote version. You won’t find the transponders alone.
At the moment xt27b are inplemented on board XHORSE XEB510EN B5 Super Remote with XT27B Super Chip. Or buy XHORSE XT1M Chip they are MQB Chips.
They have XT27B chip inside.
Problem:
Xhorse multi prog programmer suddenly reported the error “Failed to Read VPA Information. Error code 0404001f.” Force update and sync device, also tried press the RST (reset) button, still no luck. Any solution?
Solution:
Turn off multiprog device.
Wait for 1 minutes, then try again.
If not working, repeat it several times and it should be fine.
We are going to clone a computer from a Chevrolet Express 4.3 engine V6. This is an ACDelco E37 ECM. We are going to do it with Xhorse multi prog on the platform (bench mode) without opening the computer.
Select GM E37->Chevrolet->Express 1500, we see the ID, the type of unit that is a Chevrolet Express 1500.
Check wiring diagram in multiprog.
We going to place the PINs we have two red ones that are 12V of power supply, we have CAN H and CAN L and GND.
It is very simple to make this connection.
Read EXT eeprom
Read eeprom data successfully in 2min 24s.
Save eeprom data.
Read EXT flash.
Save flash data.
Connect donor ECM with xhorse multi-prog follow the same wiring diagram.
Backup donor ECM eeprom and flash.
Then write original eeprom to donor ECM.
Write original flash data to donor ECM.
Verify checksum.
Checksum calculation successful.
Write flash takes longer, 9min 14s.
Clone E37 ECM successfully.
Install donor ECM to vehicle.
Car starts fine. It works perfectly.
Problem:
My Xhorse SW-007 smart watch hands not moving, it is not working. Any solution?
Solution:
Press the red arrow randomly (marked picture below) to see if the yellow arrow lights up. If it does, watch battery is dead, replace the watch battery.
If yellow light does not turn on, the smart watch PCB board battery is dead, change battery on the main board.
People often ask what option in the xhorse mini key tool to generate Toyota Camry 2020 HYQ14FBC remote using Xhorse XM38.
Question:
Today I tried to make a key for Camry 2020 USA. FCC ID HYQ14FBC.
Not a single software worked, the car simply does not see this key. What are the options?
Here is the clue.
You can generate under this option:
Camry (A9) 18-2022 312.1/314.35
Review:
1). 0351 board HYQ14FBC/HYQ14FLA. Worked perfectly on 2020 Toyota Camry USA, all buttons works correctly out of the gate.
2). 2024 Toyota Camry/PTS/AAK made in USA, programmed successfully. All buttons work.
3). 2020 Prius generated under this option, all works.
4). Camry 2019 US, programmed successfully. All buttons work.
One of our customers has managed to read Mercedes Delphi CRD3.10 ECU with Xhorse Multi Prog.
Select MB Delphi CRD3x.x TC1797 protocol.
Boot is a different pinout. If your ECU is on service mode you need read in boot mode.
Pay attention to 2 resistors. 2x 1k resistor.
Multi prog will show you wiring diagram.
This is a Jeep control board with M95320 eeprom chip. We will show how to read this chip using Xhorse Multi Prog without laptop and PC software.
Connect M95320 EEPROM IC chip and Multiprog via a goog 8-pin clip adapter.
In multi prog, select Chip operation->M95XXX->M95320->Status
Read chip.
Read eeprom successfully. Then save data.
You can see file in Files folder.
You can save it to local to this or you can share it with you are connected to a Wi-Fi.
To program Isuzu D-Max 24C08 immobilizer keys you have to disassemble the immo box and read the data to calculate the password. Here we will show how to read immo data and pin code with xhorse vvdi prog.
Disassemble instrument cluster
Find Passive Entry and Start system module
Take out the inner circuit board and find the chip IC (24C08). This IC is a narrow-body chip, smaller than the common 8-pin one.
Read 24C08 data with xhorse vvdi prog programmer.
Find the password through the data. The password is directly displayed in the status area in reverse order. The actual password is 4043.
Then generate xhorse remote.
Program remote with OBD programmer with pin code.
