Will Xhorse Super Chip Clone Mercedes ID33?

 Problem:

It is a  Mercedes G 300 Worker (W461) year 2012, chip ID33. Chip clone with vvdi super chip and mini key tool success, but starting no.

Its an OBD or read on bench job?

Solution:

It is an ID33 rolling and can’t be cloned. It will clone successfully but won’t start the vehicle more than once. It’s a rolling code transponder.

It works on Renault and other mid-range vehicles, but it doesn’t work on Mercedes because it’s a rolling code, it only turns on once and then it doesn’t function anymore.
You can’t generate those chips with the majority of the programs, only tango original,kr55 or avdi original. If you don’t have it you can’t get it done, and it’s an EEPROM job the mcu has to be desoldered.
Take out immo read with programming tool (best desolder MCU ) generate chip with and key tool ( even Gambit can do the chip by dump ) tango, zedbull , anything that makes old mercedes with id33.
The process is simple to ews keys for BMW.
Kr55 best one tool for whole job if you have it.

http://blog.vvdishop.com/possible-to-clone-ews3-ews4-key-with-xhorse-super-chip/

FYI:

Clone Renault Clio ID33 car will start. ID33 for clio is fixed code, not rolling code as Mercedes.

Renew Chrysler 6-Button Fobik Key Fob by Xhorse Key Tool Max

 The Chrysler 6-button Fobik key fob is cheap $8 only.  But if the key wasn’t programmed to car and did not work so we can renew it.

Unlocking and renewing a 6-Button Fobik key fob using the Xhorse VVDI Key Tool Max

Select Remote Renew-Remote Renew- Chrysler/Jeep/Dodge- IYZ C010C M3N5W785

Check wiring diagram and connect remote with xhorse key tool max via renew cable

Press UNLOCK

Renew in process, wait until finished

Now the remote works successfully.
We can also get the actual renew adapters that xhorse sells. It’s much easier and less time consuming than soldering the wires to renew. It also helps renewing when you try to find some of the older BMW or Mercedes keys that are always sold out that you can buy used keys that need renewed.

Xhorse VVDI2 Frequency Test in Chinese Screen?

 Problem:

I tried to test key frequency with xhorse vvdi2, press “F” and the small screen turn to Chinese. How to change the screen to English?

 Solution:

Press both “F” and “T” buttons for 3s, the screen will turn to English.

Xhorse Key Tool Max Pro Add BMW CAS3 Key via OBD

 Xhorse VVDI Key Tool Max PRO is able to add BMW CAS3 IMMO key by OBD. Following I’m gonna show how to do.

 

1. Read IMMO Data

Plug Key Tool Max PRO cable into OBD interface.

Insert working key to turn ignition on.

Immo programming >> BMW >> Automatically diagnose models

The current system type is detected as CAS3++(ISTAP), about to enter the system operation interface, please wait…

 

Read key information >> Yes – add key >> Yes

Warning: this operation requires the CAS to be installed on the car, and operation on the platform may cause the steering lock failure!

Press “Yes” to continue.

 

Current CAS is ISTAP version, we need flash CAS firmware to continue OBD operation.

Flash firmware need about 10 minutes. Make sure your notebook and car with enough power.

Suggestion1: if the car is low power, supply extra power to car.

Suggestion2: if you have enough time, you can read CAS flash and eeprom before continue.

Press “Yes” to start flash CAS firmware.

 

The dealer key should be taken away from ignition switch.

If key is keyless, please move it out of car.

If there’s no key in ignition, continue anyway.

Press “OK”.

 

Wait processing…

 

Insert key to ignition and switch on.

The dealer key should be taken away from ignition switch.

If key is keyless, please move it out of car.

If there’s no key in ignition, continue anyway.

Press “OK”.

Reading key data success.

Save data file.

 

2. Make Dealer Key

Prepare dealer key with programmer >> Select key position: key 3

CAS key data is encrypted, support make dealer key for it. Once failed, please contact the dealer!

Try BMW protocol…

Please put new key into VVDI Key Tool Max PRO programmer.

Is the current key a smart key? No

Make dealer key success.

 

3. Add Key

Add key >> Yes

Please put new key into VVDI Key Tool Max PRO programmer.

Try BMW protocol…

Is the current key a smart key? No

The dealer key should be taken away from ignition switch.

If key is keyless, please move it out of car.

If there’s no key in ignition, continue anyway.

OK>> OK

Wiring data success.

New dealer key success written to CAS system.

You can start engine with new key now. If cant, please use the original working key first.

 

The new key can start the engine.

And its remote works fine.

Perfectly done.

https://www.vvdishop.com/service/vvdi-key-tool-max-pro-add-bmw-cas3-key-via-obd.html

VVDI Prog Read Volvo XC60 MC9S12XDT384 1L15Y

 Here comes the wiring diagram pinout of Volvo xc60 P31318792 Mcu Mc9s12xdt384 unsecured 112pin 1L15Y.

Xhorse vvdi prog read it without issue, but not showing wiring.

The pictures of conections between module and vvdiprog.  Shared by Mr.Vlahov.

Xhorse VVDI2 7.2.6 Upgrade Failed Solution

 Here is the working solution if failed to update xhorse vvdi2 to version 7.2.6.

One of our customers tried to update vvdi2 to 7.2.6 but failed, it gave error code (6:03:A0:81) Upgrade Failed.

Solution:

1.Change another USB cable or operating system (i.e Windows 7)

2. If still not working, update your Xhorse Upgrade Kit to V1.7.7, then update vvdi2 to 7.2.6

Xhorse VVDI Prog Read and Write Peugeot Boxer DCU102

 Peugeot Boxer DCU102 mcu ST10F276 successfully cloned with xhorse vvdi prog.

vvdi prog does not show the wiring diagram, here is the connection from our customer  Mr. Silviu Cocolos

Hope it helps.

Xhorse VVDI MB Adds Benz G W463 2013 BE Key

 Following I’m gonna show how to use Xhorse Dolphin XP005 + VVDI MB BGA Tool to add a BE key for Mercedes Benz G W463 2013. Dividing into 2 parts: key cutting & key adding.

Key Cutting

Having a working already, just decode it to cut a new one.

Install the working key on the Dolphin XP005 clamp.

 

Connect VVDI Key Tool Max to the machine:

Universal key duplication >> 2 track external >> Tip align >> M2-B clamp >> Decode key

Xhorse Dolphin will start decoding automatically…

 

Change a key blank on clamp after completed.

Cutting key >> Continue

Wait until cutting finished.

 

Key Adding

Next, let’s start programming a new VVDI BE Key.

Connect VVDI MB Tool to car, open software:

Step1.

EIS Tools >> Read EIS data

Reading data success.

Save EIS data.

 

Step2.

Password calculation >> Chassis: W166, 197, 212, 218, 246 >> Data acquisition

Insert working key to EIS before press OK.

Take working key out of EIS before press OK.

Insert working key to EIS before press OK.

If key can not finish synchronize, please try the following step when ask you insert key to ignition: insert key and start engine >> switch off >> switch on.

Insert working key to VVDI MB IR reader before press OK.

Insert working key to EIS before press OK.

Insert working key to VVDI MB IR reader before press OK.

Save data file.

Acquisition finished, upload the saved data with “Upload data” for password.

 

Upload data >> Select data file

Upload success!

 

Selected “Auto refresh”>> Query result

Are you sure to start auto refresh? Yes

Copy key password.

Step3.

Prepare key file >> Load EIS file >> Paste password >> Selected a key position: key 8 >> Prepare key file >> Save key file

 

Step4.

Put the new VVDI BE Key Pro into MB Tool.

Read Write Key >> Other function >> Set key remote frequence/Update MB smart key >> 433Mhz >> Set frequence

Set frequence success!

 

Identification key >> Load key file >> Selected key 8 file >> Write

Writing data success.

 

Test the new key, it can start Mercedes normally.

Remote works OK.

Perfectly done.

www.vvdishop.com

http://blog.vvdishop.com/xhorse-dolphin-xp005-vvdi-mb-tool-add-benz-g-w463-2013-be-key/