VVDI Prog 4.6.0 Renew PCF79XX Remotes to BMW E/F series

This is how to renew 315 868 433 remotes to BMW E & F series, using Xhorse VVDI Prog and PCF79XX adapter version 2.

What do you need prepare for BMW remotes renew:

VVDI Prog programmer

PCF79XX adapter

BMW remote (315MHz/433MHz/868MHz)

What kind of BMW remote VVDI-PROG supports:

BMW E SERIES

ORIGINAL 315  Need PCF79XX adapter

ORIGINAL 868  Need PCF79XX adapter

THIRD PARTY  Need PCF79XX adapter

BMW F SERIES

315 REMOTE  Need PCF79XX adapter

433 REMOTE  Need PCF79XX adapter

868 REMOTE  Need PCF79XX adapter

How to connect the BMW remote chipuse to PCF79XX adapter:

Put the chip in the IC socket

Desolder the original battery before writing the file

BMW-E-SEIRES-THIRD-PARTY-REMOTE-RENEW-CHIP: PCF7953/PCF7945

BMW-E-SEIRES-THIRD-PARTY-REMOTE-RENEW-IN-CIRCUIT

BMW-E-SEIRES-ORIGINAL-REMOTE-RENEW-CHIP: PCF7953/PCF7945

BMW-E-SEIRES-ORIGINAL-REMOTE-RENEW-IN-CIRCUIT

BMW-F-SEIRES-REMOTE-RENEW-CHIP: PCF7953

BMW-F-SEIRES-REMOTE-RENEW-IN-CIRCUIT

PCF7953/PCF7945 adapter version 2 required!!!!!!!!!!!!!

How to renew BMW remotes with VVDI Prog:

This is a BMW remote review from a customer who has good success.

I did renew 2 keys! Renew BMW series E 868 key – 100% OK using vvdi prog v4.6.0. Both worked and now are programmed to cars! 

Only thing you need to disconnect from PCB is battery while writing the renew file.

I think that is only for those who have older version of that adapter. Older version came with 33 ohm resistor and later they decided that it is not needed and newer adapters like mine came with 0 ohm resistor that is just connecting both sides together without resistance.
If you have that 33 ohm resistor then remove it and short-connect it.
If you have 0 ohm resistor, then don’t mind that first box in connection diagram. It’s not for you.

I did it in circuit.

 www.vvdishop.com

http://blog.vvdishop.com/vvdi-prog-v4-6-0-renew-pcf79xx-remotes/

Free Download Xhorse VVDI Prog V4.6.0 (2017-07-26)

Original Xhorse VVDI PROG programmer latest software version V4.6.0 update fix bugs and add many new ECUs  (2017-07-26)

————————————-
VVDI-Prog v4.6.0 (2017-07-26)
* This version DON’t need update firmware
* Fix some bugs
+ Add VVDI PROG USER MUNUAL 4.6.0 version in Doc folder
* Change some RENESAS-V850 chips DFLASH size to 64KB
* Fix GM-BCM3 option
* Fix V850E2 series diagrams
* Change KESSY(2008–) diagram

(Need to use with VVDI2,support Touareg, Bentley, A8, Cayenne, Phaeton with kessy module
(IMMO4 system) after 2008)
+ Add V850E-SK3H,V850-SJ3H series diagrams
+ Add NM93CS06, NM93CS46, NM93CS56, NM93CS66, FM93CS06, FM93CS46,FM93CS56,
FM93CS66 options in <1-EEPROM&FLASH>-><FAIRCHILD>
+ Add M93S06, M93S46, M93S56, M93S66, ST93CS46, ST93CS47, ST93CS56, ST93CS57,
ST93CS66, ST93CS67 options in <1-EEPROM&FLASH>-><ST>
+ Add D80(ADAPTER), D160(ADAPTER), M350803(ADAPTER), M350806(ADAPTER), M35080V6(ADAPTER),
M35080VP(ADAPTER) options in <1-EEPROM&FLASH>-><ST>(Need M35080/D80 ADAPTER)
+ Add MC9S12HN64_UNSECURED, MC9S12HZ64_UNSECURED, MC9S12HN64_SECURED,
MC9S12HZ64_SECURED options in <2-MCU>-><MOTOROLA-MC9S12>
+ Add ST72321(R/AR)6, ST72F321(R/AR)6, ST72321(R/AR/J)7, ST72F321(R/AR/J)7, ST72321(R/AR/J)9,
ST72F321(R/AR/J)9, ST72521B(R/AR)6, ST72F521(R/AR)6, ST72521B(M/R/AR)9, ST72F521(M/R/AR)9 options
in <2-MCU>-><ST-ST7>
+ Add SPC5606S option in <2-MCU>-><ST-SPC560XXXX>
+ Add ME7.5.20(ST10F275) option in <3-ECU>-><VOLKSWAGEN>
+ Add KESSY(2008–) option in <4-IMMOBILIZER>-><AUDI>
+ Add KEYLESS-ENTRY-MODULE(2009–)option in <4-IMMOBILIZER>-><GM>
+ Add HAVAL-H9-BCM(D70F3632) option in <4-IMMOBILIZER>-><GREATWALL>
+ Add BCM(2009–) option in <4-IMMOBILIZER>-><LANDROVER>
+ Add XINBAO(MC9S08LG16) option in <5-DASHBORAD>-><CHANGAN>
+ Add CRUZE(D70F3423) option in <5-DASHBORAD>-><CHEVROLET>
+ Add DASHBORAD(2013–)(SPC5604S), DASHBORAD(2013–)(SPC5606S), FIESTA(3L16Y),
FOCUS-C-MAX(2009) options in <5-DASHBORAD>-><FORD>
+ Add BESTURN-B70-SRS(D70F3623) option in <7-ARIBAG>-><FAW>
+ Add ACCORD-SRS(SPC56AP54L3) option in <7-ARIBAG>-><HONDA>
+ Add SRS-VW20(SPC560P50L3) option in <7-ARIBAG>-><VOLKSWAGEN>
+ Add A4L-LEW-MODULE(2013) option in <8-OTHER>-><AUDI>
+ Add EVOQUE-EPB-MODULE(2013) option in <8-OTHER>-><LANDROVER>

Free Download VVDI Prog programmer V4.6.0 software
https://mega.nz/#!GoYhgIoS!Q13Sw-b6sDxld2mJSn5HunYYHZwg7EdXqF_xa3V_ecw
password:123456

http://blog.vvdishop.com/free-download-xhorse-vvdi-prog-software-v4-6-0/

VVDI Key Tool V2.3.9 Unlock BMW KeyLess Successfully

Xhorse Vvdi Key Tool remote maker updated to v2.3.9 successfully& tested as demonstrated below by the 1st owner of Vvdi Key Tool Mr. Mohamed Gulam, bmw KeyLess unlocked successfully as well for testing tool capabilities

Vvdi Key Tool Europe, Southeast Asia, Middle East, North America, India, English ( Eu, eu-en, se, se-en, me, me-en, na, na-en, in, in-en ) version finally announced for and released V2.3.9
Release Date 20th July 2017

https://mega.nz/#!Ab5UzQIJ!Oz9tkehSW7CuZz6zvKxVwvq9_2XZpdtCjn0xJRQjP_c

Vvdi Key Tool Latest update Proximity Remotes / KeyLess Go Unlocking Diagrams added below.

There you go, when vvdishop.com said 86 type & model were added, we meant so for real, enjoy  and don’t forget to count them 

Download in PDF format via the link below.

VVDI Key Tool Renew Unlock Wiring Diagram User Manual

http://blog.vvdishop.com/vvdi-key-tool-v2-3-9-bmw-keyless-unlocked-successfully/

VVDI2 make a dealer key on VW Transporter UDS System

If you have Xhorse VVDI2 VAG key programmer to add dealer key on VW Transporter/Caravelle T5 2011, but not work, you must read this post, the problem is finally solved.

Problem description:

VW Transporter/Caravelle T5 2011. Had an existing working key and used Xhorse VVDI2 to make a dealer key on a UDS cluster but something went wrong or more likely I did something wrong. It says 2-2 on the cluster and lights go off as if programmed but once cranked it starts and dies and the glow plug indicator light flashes. I stripped the cluster and tried with putting the cluster in to service mode but still much the same. With AD100 it says 2 keys coded and cluster in Mode 7. A friend came with his Zedfull and recoded in both keys and it said precoding ok but still the same issue. The dump of the original 24c64 and the backup I first made are attached and I’d appreciate any advice or help on this. Thanks everyone

folder: Transporter T5 24c64 Original Read

Folder: Transporter T5

Advice:

Config: This value contain car manufacture, key number, immobilizer status (new, learned, closed), keyless or not etc.

Your immo status is likely changed, did you press the reset immo button.

When did you made the 24c64 backups.

After entering service mode true obd, or after your keylearning procedure?

Question:

The initial backup (small file)was made before I made the key but I read the 24c64 only after it wouldn’t start. Any idea how to change the config from o7 to 06 again?

Instruction guide by senior:

go in to service mode by obd.

read immo data.

change the conf 7 in to 6.

press, write immo data.

press, reset instrument.

that should do it.

Finally! Solved

Thanks everyone. Yes it was me being stupid, I think I actually wrote the 24c64 complete file back instead of the smaller immo file. Did as advised and problem solved.

www.vvdishop.com

http://blog.vvdishop.com/solved-vvdi2-make-a-dealer-key-on-vw-transporter/

Xhorse VVDI Prog Programmer Feedback July 2017

Xhorse VVDI Prog programmer updated feedback in July 2017.

EZS VW Crafter
old version MC9S12DT256 (0L01Y) - read/write eeprom and flash OK
new version MC9S12XDT384 (1L15Y) - read/write eeprom and flash OK

cas4 1l15y R/W eeprom and flash okay
BMW FRM3 d flash r/w okay
E-series CA key write okay
W203 1J35D read / write OK cable v3
W639 545 02 08 (0L02M) W169 545 17 08 5L40K OK
W639 545 21 08 (0L01Y) W906 545 40 08 SPRINTER (0L01Y)

MCU V3 CABLE all good. 

MC9S12 V1 CABLE

A6 C7 door module D70F3626 reads OK!
A6 C7 Tailgate module D703373 read success! Had to increase the voltage to 4.7V!

http://www.vvdishop.com/wholesale/vvdi-prog-programmer.html

How to Update Xhorse VVDI Key Tool English Version to V2.3.8

Original Xhorse VVDI KEY TOOL remote maker latest English version software V2.3.8 has been verified and tested working by Xhorse engineers.  The new upgrade software adds Toyota G chip, Chrysler 4D, Ford ID83 etc clone.

VVDI Key Tool V2.3.8 Update Feature [2017-07-16] 
* * * * * * * * * * * * * *

Firmware version: V2.0.2
Attention: This update only for North American or India English version(na,na-en,in,in-en). Other languages will be released on next week, please get Device Info to check language version.
This version must be updated with V2.3.8 and above. The upgrade may take about 30 minutes
1.transponder clone
+add chrysler 4D-64(4E) clone
+add toyota-G offline clone
+add hyundai ID-70 online clone(Use Calculate option in upgrade software)
+add ford ID-83 online clone(Use Calculate option in upgrade software)
+add ID-4A identify
2.generate transponder
+add toyota-G to generate special transponder
3.remote renew
+add more than 86 remote&keyless go prox unlock
4.remote prepare
*fixed XN serial keys problem on ID47 such as suzuki
5.add more vehicles data and fixed some bugs

Free Download VVDI key Tool V2.3.8:
mega link

https://mega.nz/#!2howjaAD!TLQ8JjAkWuRbjq8ZjYqtoebKY_nAhOtUbstb1PGyID8
dropbox link
https://www.dropbox.com/s/hhfvy4qp1pgocae/KEY%20TOOL%20Update%20V2.3.8-EN.rar?dl=0

How to Update VVDI Key Tool Software?

Select “Update” option on function menu
Go to VVDI KEY Tool SYS Set to update

Connect remote maker with PC via a USB cable
Click “Update Online” button to start upgrade
Wait for update completed

www.obdii365.com

http://www.key-programmer.org/2017/07/17/free-update-and-update-vvdi-key-tool-english-to-v2-3-8/

VVDI2 is not bind to any VVDI MB Tool device? How to solve

Error when verifying VVDI normal Sub-remote pcb:

“Attention

VVDI2 SN VV20798267 is not bind to any VVDI MB Tool device!”

Solution:

Xhrose VVDI (VVDI2, VVDI MB BGA Tool) Foreign Point System is not yet available. Wait feature update.

www.vvdishop.com

http://blog.vvdishop.com/vvdi2-is-not-bind-to-any-vvdi-mb-tool-device/

Xhorse VVDI2 BMW Key Programmer Reviews

Xhorse VVDI2 BMW version key programming tool, how does it work? Here are the user feedback on bmw vvdi2.

Xhorse VVDI2 BMW  is BMW professional key programmer tool that covers full functions of BMW Multi Tool,and which is better than Multi Tool. Software and firmware both online upgrade-able.

VVDI2 BMW includes BMW OBD and CAS4 authorization, and VVDI2 BMW software language: English, Italian, Spanish, Dutch, Hungarian.

VVDI2 BMW can support not only key programming,but also km,some can do via OBD,some need CAS Plus,some need by eeprom way,like CAS4,needs to use VVDI Prog to read eeprom data,then use with VVDI2 BMW.

Xhorse VVDI2 BMW Key Programmer Feedback:

1) Cars that I have successfully done with VVDI2

2005 BMW E87 CAS3

2006 BMW E90 CAS3

2003 BMW E60 CAS2

2010 Audi A5 with Keyless Entry

2011 Audi A3
2009 VW Golf mk6

2) I tested my vvdi2 on 2008 bmw m6 today. It worked flawlessly and was a bit quicker than multi-tool.

3) I did a perfect job on 2010 bmw X5 with ISTAP today. I downgraded CAS ( I backed up eeprom with xprog first) and then retrieved key info OK. Adding key was a brieze after that. Cleared all errors, synchronized ELV. DONE

4) Hi i yesterday have bmw f10 2012 year ,read cas4+, change, write back all ok work .happy 100%

5) BMW cars I have completed with VVDI 2.
– EWS 2
– EWS 3
– EWS 3+
– EWS 4
– CAS 2
– CAS 3
– CAS 3++ (ISTAP)

I think some people need to do more research before blaming tools.

Credit to VVDI2 BMW users from DK forum.

http://blog.vvdishop.com/xhorse-vvdi2-bmw-key-programmer-feedback/

VVDI2 VAG adapt EDC16U1 ECU failed (Solution)

Problem:

Xhorse VVDI2 VAG ECU adapt doesn’t work with EDC 16U1… Tried on Seat Toledo MY05 using VW Touran ECU. Finally I disabled immo but I want to adapt it to car…

Solution:

not work because is tool old … working after 2007 (u34)
You can adapt that type of ECU via SCK

Use any u34 ECu from 2007 up and you will see.

http://www.vvdishop.com/wholesale/vvdi2-basic-module-and-vag-functions.html

http://blog.vvdishop.com/vvdi2-vag-cannot-adapt-edc16u1-ecu/