Xhorse Multi Prog Read Opel AcDelco E87 ECM

 Today I’m gonna use Xhorse Multi-Prog Programmer to read Opel AcDelco E87 emulated eeprom for a test. Includes how to read, extract, import the emulated eeprom and do mileage adjustment.

Connect device& ECU according to wiring diagram on bench.

Open Multi-Prog software,

• Read Emulated EEPROM

Read >> Yes, read emulated EEPROM

Reading data, please wait…

Data read successfully.

Save emulated eeprom to file? Yes

The operation was successful.

Extracted and saved the emulated eeprom.

Load emulated eeprom? Yes, selected the saved flash file.

Now we can get the PIN code & mileage.

Mileage is 121408.2976km

• Mileage Correction

We can also modify its mileage:

KM >> Enter new value: 40000

The mileage has been changed to 400000km.

• Extract EEPROM

Click “EE-OUT”.

Extracts emulated eeprom from Flash.

Load INT-FLASH file? Yes, selected the original flash file.

The operation was successful.

Extracted and saved the emulated eeprom file.

Load emulated eeprom? Yes, selected the emulated eeprom file.

• Import EEPROM

Click “EE-IN”.

Imports emulated eeprom to Flash.

Load the emulated eeprom? Yes, selected the emulated eeprom file.

The operation was successful.

Save the modified file? Yes

The operation was successful.

Load new FLASH? Yes, selected the new emulated eeprom file.

 www.vvdishop.com

Xhorse Multi Prog Read Mercedes MED17.7 ECU

 Xhorse Multi Prog read Mercedes-Benz S class S400 hybrid ECU successfully.

ECU: Bosch MED17.7

Follow the wiring diagram in multiprog software.

Read flash ok.

Xhorse Multi Prog Clone BMW MSV80 Success

 Xhorse Multi Prog new user report:

Clone MSV80 Siemens Protocol

Checksum by multi prog.

How to Replace VVDI Mini OBD Tool Battery if Failed to Update Firmware?

 Some users reported that they have problems updating vvdi mini obd tool firmware and sync device.

If the version is lower than 1.5.0, try several times, change PC or network, if all failed, device information is missing. Need to send back for repair.

If the version is 2.1.50, disassemble the device, replace a new battery, update firmware and sync device again.

Sync device again after replacing battery. Then update firmware via Upgrade kit again.

Follow steps below to replace battery.

Xhorse Multi Prog Read VW Passat MED9.1 ECU

 Success in reading and writing immo off for VW Passat Bosch MED9.1 ECU using Xhorse Multi Prog programmer.

Read eeprom and flash ok
write data ok in 43s.

VVDI MB Tool Benz Repair KM Car List

 Xhorse VVDI MB Tool supports writing KM (correct odometer) for the following Mercedes models:

C(W204), GLK (X204), CLK (W207), E (W212), SLS (W197), CLS (W218)
R-Class (W251), GL (X164), ML(W164)
E-Class (W211), CLS(W219)
S-Class (W221), CL (W216)
W166, W172, W246, W231
W205

Xhorse Multi Prog MB EZS Chip Crack Failed Solution

 Problem:

Xhorse Multi Prog failed to read Mercedes EZS W169. Software gives an error: “Chip crack failed. Error code 13050102, cracking failed. adjust the VDD voltage to 4-5V.
“. Any idea?

Solution:

If you don’t use lab power supply and don’t adjust the volts well you will get error. It’s not a MultiProg failure.

You have to manually modify the voltage in the software because it is at 2.7 vdd but 5v it will work.
Set it to 13.2v max amperage and set the EZS voltage to 4.9v.

www.vvdishop.com

Xhorse VVDI PROG Read 2024 Hyundai Airbag RH850

 Today we received an 2024 Hyundai airbag module. We’re gonna reset it with Xhorse VVDI PROG on bench. Before that, we should read and save its DFLASH & CFLASH of the module.

 

First, we’ll do its connection.

Connect VVDI PROG& airbag module according to wiring diagram.

Second, Open VVDI PROG software.

Type: 2-MCU

Brand: RENESAS-RH850

Chip: R7F701042

Read DFLASH…

The module is working, the frequency has been matched now.

Read DFLASH success.

Save DFLASH data file.

 

Read CFLASH…

Read CFLASH success.

Save CFLASH data file.

www.vvdishop.com

Xhorse VAG MM-007 Change VW Tiguan 2014- NEC24C64 Mileage

 How to: correct odometer on VAG NEC+24C64 2014.06- dashboard using the Xhorse iScancar VAG MM-007 service tool.

 

Model example: VW Tiguan 20TSI 4motion DSG7 swap cluster

Record original mileage: 114, 625km
Select Special Function from main menu
Then KM calibration-> Dashboard
Select instrument type: NEC+24C64 (2014.06- VW/Skoda/Seat)
Press OK to continue

Xhorse VAG MM-007 reads old KM, check and confirm
Then input the new KM

Choose login method: 1 (only 1 or 2)

The dashboard will turn black during the writing km procedure. It is normal.

Dash will be reset after writing new KM successfully.

Check the new mileage.

It corrects mileage successfully.

www.vvdishop.com