Xhorse VVDI Tools, VVDI2, VVDI MB, VVDI Prog, VVDI key tool, VVDI BMW etc software & firmware download, update and technical support from vvdishop.com.
Problem:
Xhorse vvdi key tool max failed to connect to Bluetooth, my mobile phone failed to detect xhorse Bluetooth. Any idea?
Solution:
You don’t need to connect key tool max with mobile phone via Bluetooth.
Xhorse Key Tool Max can be used as a mobile phone with an operation screen for other xhorse tools Mini Prog, Dolphin XP005, Mini OBD Tool.
Here’s a quick easy guide on renewing Mercedes Benz ECU ME9.7 with xhorse vvdi mb tool through OBD
For connection, check the previous post: connect VVDI MB Tool to ME 9.7 ECU
Read ECU information
Get Erase password
Press Renew
If failed to erase target unit, renew again
Save data
How to use Xhorse VVDI Key Tool Max to clone a spare key for 2014 Fiat Doblo? It’s very fast and easy, following I’ll show the procedure.
An original working key, a blank new key and a VVDI Super Chip are required.
Put the original key into Key Tool Max coil, press
Transponder clone >> Read transponder
Information has read out, it’s cloneable.
Just follow the instructions to clone, continue to press
Clone >> Start clone >> 46 transponder clone >> Original key clone(recommended)
Note: don’t remove the original key
It’s asking to sniff at the data, so what I have to do is to put the antenna near the ignition and turn it on.
Put the original key into Key Tool Max coil again as required.
Wait collecting data…
Calculate success.
Take out the original key, then put a Super Chip into coil.
Write data success.
Let’s put the Super Chip inside a new key shell to have a test.
As you can see, it starts the vehicle.
Let me try the original one, both can start the car.
It is a very simple process with VVDI Key Tool Max to clone a key for 2014 Fiat Doblo. It only takes me 4 minutes to finish.
How-to: BMW M3 2011 CAS3+ ISTAP 0L15Y spare key programming with xhorse mini prog and key tool max.
1.Read EEPROM with VVDI Mini Prog
Remove CAS3+ Module
Connect mini prog CAS3 solder free adapter with CAS3 module
Follow mini prog app prompts to read EEPROM and save data
2.Make dealer key with xhorse vvdi key tool max
In key tool max app, select Special function -Immo data tool- BMW- CAS3+ 0L15Y
Then load eeprom read by the mini prog
Write key with dump
Reinstall CAS3+ module.
Test new key and remote control.
Done.
Xhorse released new optional Audi BCM2 solder free adapter. Here are frequently asked questions and answers of the new adapter.
Q: Is it for xhorse key tool plus only or mini prog?
A: The Audi bcm2 adapter is compatible with vvdi key tool plus and vvdi2 +vvdiprog.
Q: does it support Audi A6L all keys lost without synchronize data?
A: No, A6L/A6 AKL still requires sync data from third party. But the adapter will help read BCM2 Immo data when lost all keys. A4L, A5, Q5 all keys lost does not require sync data.
Check the table of the adapter capabilities below
| Add Key | All Keys Lost | |||
| Read BCM2 data | Synchronize data | Read BCM2 data | Synchronize data | |
| A4L/A5/Q5 -2013 | OBD | No | OBD/some need remove BCM2 | No |
| A4L/A5/Q5 2013-2019 | Xhorse BCM2 Adapter | No | VVDI BCM2 adapter | No |
| A6L/A7/A8 -2013 | OBD | Obtain from working key | OBD/some need remove BCM2 | Obtain from third party |
| A6L/A7/A 2013-2019 | OBD | Obtain from working key | VVDI BCM2 adapter | Obtain from third party |
Q: Does the cable work with vvdi2 as well?
A： Yes, vvdi2 upcoming update will adds this function. But requires working with vvdi prog to read BCM2 data.
Q: Can I do 2013-2018 A4 all keys lost via OBD with xhorse key tool plus and this adapter?
A:No, for A4 from 2013-2018 you must read BCM2 Immo data with the new solder free adapter. pre-2013 A4 supports BCM2 data reading via OBD (does not require sync data)
Q：Can I read the BCM2 Immo data without soldering if I buy this adapter?
A: Yes, you can. requires the xhorse Audi bcm2 adapter set which has 6 adapters included.
Q: When will it be available?
A: it will be available in the beginning of Sep. 2021.
Q: How much does it cost?
A: pre-order price is 100USD. price will goes up when it is available. First come first served.
Q: Does it require token? what about the update?
A：It is token free. Free update as other xhorse tools.
Q：Does it require special key to program?
A：You can use regular 754J key on the aftermakert.
Here is our suggestion to solve vvdi prog problem reading st 95xxx eeproms.
The problem goes like this:
I have problems read st 95xxx eproms. Have tried 9508. 95128. 95256. 95320.
All soldered to xhorse vvdi prog EPROM adapter.
every single leg is clean, soldered perfectly but not working
reading error, write say ok but all 00
i tried with 12v connected and unconnected. Now difference.
Here is pic. Everytime i solder 95xxx EPROM vvdi prog don’t read. But if i put the same EPROM adapter on my orange 5. It reads it without problem.
Suggestions:
No problem with vvdi prog. Need to use the clip adapter and read on board i do fem bdc without any problems. Clean glue off with blade check data a few times if match and done.
Always i don’t solder chip off fem module it could be a disaster if it breaks or overheats. You must find how to turn clip 1st pin and you must clean glue off legs no problem to read then. Without cleaning cant get contact.
use vvdi clip adapter here
http://blog.vvdishop.com/xhorse-vvdi-prog-95xxx-read-error-solution/
With the help of vvdishop.com engineer, my problem was settled.
The problem goes like this: xhorse vvdi prog said chip not connected when i tried to read mcu Tms370 from an Opel 2008. I did desolder chip onto the TMS370 adapter.
Connection is not the problem. You use Opel Immo menu. It is wrong. Don’t put 12v.
